The specification says that the geometry shader should exit if the
number of emitted vertices is bigger or equal to max_output_vertices and
we can't do that because we're running in the SoA mode, which means that
our storing routines will keep getting called on channels that have
overflown (even though they will be masked out, but we just can't skip
them).
So we need some scratch area where we can keep writing the overflown
vertices without overwriting anything important or crashing.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Jose Fonseca <jfonseca@vmware.com>
Can happen if we were using stream output without geometry
shader, by returning early we avoid a crash.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Jose Fonseca <jfonseca@vmware.com>
This is a basic implementation of the pipeline statistics in the
draw module. The interface is similar to the stream output statistics
and also requires that the callers explicitly enable it.
Included is the implementation of the interface in llvmpipe and
softpipe. Only softpipe enables the pipeline statistics capability
though because llvmpipe is lacking gathering of the fragment shading
and rasterization statistics.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Jose Fonseca <jfonseca@vmware.com>
The issue with SOA execution and end_primitive opcode is that it
can be executed both when we haven't emitted any vertices, in
which case we don't want to emit an empty primitive, and when
the execution mask is zero and the execution should be skipped. We
handled only the latter of those conditions. Now we're combining the
execution mask with a mask created from emitted vertices to handle
both cases. As a result we don't need the pending_end_primitive
flag which was broken because it was static and could be affected
by both above mentioned conditions at run-time.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Jose Fonseca <jfonseca@vmware.com>
Same as with llvmpipe: we can't be divind/moding by zero and we
need to make sure that dividing/moding by zero produces 0xffffffff.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Jose Fonseca <jfonseca@vmware.com>
TGSI_OPCODE_IF condition had two possible interpretations:
- src.x != 0.0f
- Mesa statetracker when PIPE_SHADER_CAP_INTEGERS was false either for
vertex and fragment shaders
- gallivm/llvmpipe
- postprocess
- vl state tracker
- vega state tracker
- most old drivers
- old internal state trackers
- many graw examples
- src.x != 0U
- Mesa statetracker when PIPE_SHADER_CAP_INTEGERS was true for both
vertex and fragment shaders
- tgsi_exec/softpipe
- r600
- radeonsi
- nv50
And drivers that use draw module also were a mess (because Mesa would
emit float IFs, but draw module supports native integers so it would
interpret IF arg as integers...)
This sort of works if the source argument is limited to float +0.0f or
+1.0f, integer 0, but would fail if source is float -0.0f, or integer in
the float NaN range. It could also fail if source is integer 1, and
hardware flushes denormalized numbers to zero.
But with this change there are now two opcodes, IF and UIF, with clear
meaning.
Drivers that do not support native integers do not need to worry about
UIF. However, for backwards compatibility with old state trackers and
examples, it is advisable that native integer capable drivers also
support the float IF opcode.
I tried to implement this for r600 and radeonsi based on the surrounding
code. I couldn't do this for nouveau, so I just shunted IF/UIF
together, which matches the current behavior.
Reviewed-by: Roland Scheidegger <sroland@vmware.com>
Reviewed-by: Marek Olšák <maraeo@gmail.com>
v2:
- Incorporate Roland's feedback.
- Fix r600_shader.c merge conflict.
- Fix typo in radeon, spotted by Michel Dänzer.
- Incorporte Christoph Bumiller's patch to handle TGSI_OPCODE_IF(float)
properly in nv50/ir.
This patch adds PCI IDs for Bay Trail (sometimes called Valley View).
As far as the 3D driver is concerned, it's very similar to Ivybridge,
so the existing code should work just fine.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Assume the maximum pixel size (16 bytes per pixel). In addition to
moving redundant malloc and free calls outside the loop, this fixes a
potential resource leak when a surface is mapped and the malloc fails.
This also makes blit_nearest look a bit more like blit_linear.
v2: Use MAX_PIXEL_BYTES instead of 16. Suggested by Ken.
Signed-off-by: Ian Romanick <ian.d.romanick@intel.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
This was originally discovered by Klocwork analysis:
Possible memory leak. Dynamic memory stored in 'srcBuffer0'
allocated through function 'malloc' at line 566 can be lost at line
746
However, I think the problem is actually much worse. Since the memory
is freed after the first pass through the loop, the released buffer may
be used on the next iteration!
NOTE: This is a candidate for stable release branches.
Signed-off-by: Ian Romanick <ian.d.romanick@intel.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
There is a hardware bug on Cayman where a BREAK/CONTINUE followed by
LOOP_STARTxxx for nested loops may put the branch stack into a state
such that ALU_PUSH_BEFORE doesn't work as expected. Workaround this
by replacing the ALU_PUSH_BEFORE with a PUSH + ALU
Fixes piglit tests EXT_transform_feedback/order*
v2: Use existing loop count and improve comment
v3: [Vadim Girlin] Set jump address for PUSH instructions
NOTE: This is a candidate for the 9.1 branch
Signed-off-by: Vadim Girlin <vadimgirlin@gmail.com>
Instead of emitting configuration values (e.g. number of gprs used) in a
predefined order, the LLVM backend now emits these values in
register/value pairs. The first dword contains the register address and
the second dword contians the value to write.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Brian Paul